Close Window

Model 325 Parts List

 

PARTS FOR MODEL 325 ELECTRIC EEL
Model GE-30A Clutch Assy (Front slip clutch)
(This Clutch Same as E-30 Clutch used on Model C Units with Exception of GE-32 Drive Member)
GE-32 Drive Member
F-10 Pin
SC-14A Drive Fitting Assembly
......Consists of:
..............(1) SC-10 Female Front Fitting
..............(1) SC-14 Shaft
..............(1) 3/16" x 11/8" Spirol Pin
GE-16A Counter Assembly Complete
Consists of:
..............GE-11 Countershaft Bracket
..............GE-16 Countershaft
..............GE-16-1 Countershaft Adapter
...............PB-1 Pillow Block W/ Bolts (2 Req'd)
...............3/8" x 1 1/2" Carriage Bolt W/ Nut & Lk Wshr
GE-10 Bracket
GE-15 Countershaft Pin
#4L320 V Belts

ENGINE REPLACEMENT - (BRIGGS & STRATTON)
Briggs & Stratton 5 H.P. IC Gas Engine (Part #13152-2049) (45 lbs)
#27313 Gasket For B & S Engine & R-2 Housing
Ring Gear
Throttle Control W/ Cable (Can Be Shortened For Clinton Engine)

ENGINE REPLACEMENT KIT FOR REPLACING CLINTON W/ BRIGGS & STRATTON
Engine Repl Kit Required For Replacing Clinton Engine W/ Briggs & Stratton
......Includes: 5 H.P. Briggs & Stratton IC Gas Engine, R-2 Rear Clutch Housing

......................and GE-7 Flywheel

PRODUCTION CHANGES
..-..Changed From Clinton Engine To Briggs & Stratton Engine At Serial # 1072 .....(Sept. 1978).
.....Clinton Model # Was 498-0361-108

..-..Changed Countershaft Assembly From GE-11A Casting With Bearings To ......Pillow Blocks At Serial # 1163 (Aug. 1979)

..-..New Style GE-4 Coupling Started W/ Serial # 1428 (Feb. 1984)
.....The Coupling is Keywayed Instead of Splined

..-..Changed to GE-92 Transmission on Serial # 1705 (Nov. 1988) Plus Serial # .....1684. This also changed
.....The Hole Pattern on the GE-8 Transmission Ext Housing.

PARTS FOR MODEL 325 ELECTRIC EEL
GE-4 Coupling (Keywayed) and GE-9 Extension Shaft Assembly
GE-8 Transmission Extension Housing
GE-14 Spacer
GE-17 Front Bearing Retainer W/Lock Nut
GE-18 Bearing Bracket
GE-19 Gear Shift Extension
GE-20 Small Two Groove Sheave For Countershaft
GE-21 Large Two Groove Sheave For Extension Shaft
6304ZZ Ball Bearing
A-811-6 Front Bearing
4.10 - 350 x 6 Wheel & Tire (4 Required)
3/8" x 1 3/4" Spuart Head Bolt & Nut
1 1/4" Lock Nut..............................(For GE-17 Front Bearing Bracket)
Key - 3/16 x 3/16 x 1"....................(For GE-9 Ext Shaft & GE-16 Countershaft)
# 5000 - 206 Retaing Ring...........(For GE-8 Ext Shaft Housing)
Gear Shift Knob
#9 Woodfuff....................................(For GE-9 Ext Shaft & GE-7 Flywheel)
1/4" x 1" Spirol Pin.........................(For GE-9 Ext Shaft)
3/8" Thumb Screw..........................(For L-2 Handle)
L-2 "U" Shaped Handle.................(Effective Aug. 1978)
GE-22 Pulley Guard.......................(Started W/ Serial # 534)
Snap on Clip...................................(Holds Throttle Cable To Handle)

REPLACEMENT TRANSMISSIONS AND KITS
For S/N 1705 (Nov' 88 And Later Plus S/N 1684
..GT-92 Replacement Transmission Only
For S/N 1429 (Jan '84) Through S/N 1704 (Nov. 88) Excluding # 1684
..Replacement Kit Including GT-92 Transmission and GE-8 Ext Housing
For S/N 1428 & Prior (Jan '84)
..Replacement Kit Including GT-92 Transmission, GE-8 Trans Ext Housing
..And GE-4 & GE-9 Assembly

TRANSMISSION CONTROL HOUSING ASSY (Shifter Assembly)
For GT-92 Transmission (S/N 1705 and Later Plus S/n 1684)
For GT-92 Transmission (S/N 1704 & Prior Excl. 1684)

CLUTCH PARTS
Rockford Clutch Pressure Plate Assembly (Bolts to Flywheel)
Clutch Friction Disc Assembly
# CLA-2131-2AB Throw Out Bearing
GE-2 Clutch Pedal Bracket
GE-3 Clutch Pedal
GE-5 Clutch Throw out Fork
GE-5-4 Fingers (For GE-5 Throw Out Fork - Two Req'd)
GE-6 Hinge Pin
GE-7 Clutch Drive Member (Flywheel)
GE-12 Clutch Tie Rod
R-1 Clutch Housing (Front)
R-2 Clutch Housing (Rear)
GT-10 Thrust Bearing
B-810 Bearing (Replaces B812)
A-1155-2 Bushing
# 10527 Oil Seal for R-2 Casting